Fermentation Equipment & Solutions

Seeding Tank

The seeding tank is a device for expanding the industrial cultivation of microorganisms,
widely used in the fermentation industry. | t can achieve heat exchange, ventilation, stirring
and other functions, and is a fully enclosed and hygienic fermentation specialized equipment.

Technical Features

•  The sealing performance can ensure sterilization operation.
• Less internal accessory equipment, smooth surface.
• Enough strength and long working life.
• The design pressure: 0~0.5MPa
• The design temperature: 0~200°C
• Tank material: SS304-316L

Fermentor

The fermentor are the main equipment for industrial microbial cultivation.

Technical Faetures:

• The control system is easy to operate and performance is stable.
• The inoculation way is diverse and reliable.
• Sterilizing online, safe and reliable.
• In the course of agitation, the defoaming device keeps no bubble accumulation.
• Through the stirring and uniform mixing to get better fermentation.
• The fully enclosed design can ensure that the materials are always under
  non-pollution environment.
  Tank material: stainless steel
• The design temperature: 0~200°C
• The design pressure: 0~0.5MPa

Tube and Shell Evaporator

MKTE series multi-stage falling film evaporator concentrates the solution by means of vaporizing the thin solution through film-falling principle. It adopts continuous production and its features in high concentration ratio (1/5-1/10), large viscosity scope (> 400CP), good heat-transferring effect, large processing capacity etc. In this case, it can be introduced on vaporizing materials which are high heating sensibility, high concentration, high viscosity and corrosive. Therefore, it is widely used in fermentation, food, milk, alcohol and starch industry. The equipment with a higher heat-transferring ratio, so the temperature difference requested is small. It can be combined into two
stage, three stage, four stage, or multi-stage evaporator system on the basis of different material characteristics and evaporating concentration. In addition, it can be used as waste-heat evaporator with the resources of waste steam from bundle dryer or other heating resources with low thermal! value such as condensate steam. In this way, raw steam consumption can be greatly reduced for energy saving. It is economically beneficial when waste steam can be completely used and raw steam is saved.

Crystallizer

MKCL Crystallizer is cooling crystallizing equipment. During the work process, crystal slurry with a certain saturation level is injected from the feeding port on the upper part of the crystallizer, gradually cooling down under the action of cooling water, and the crystals gradually grow to complete the crystallization process. It is widely used in the crystallization of chemical products such as glucose solution, MSG, xylose, xylitol, and salts in the chemical industry.

Jet Cooker

MKJC series full automatic liquefaction jet cooker is a new type of liquefaction injector, which stands a leading level of the similar products.
There is no rusting, no jamming in it. In the steam pressure over than 0.5MPa, the starch can be liquefied by the jet cooker completely, high liquefied substrate concentration, high steam thermal efficiency and high conversion rate of starch.

Plate Filter Press

MKFP series plate filter press is usually used for solid-liquid separation in coal, oil, chemical, textile, food, pharmacy, metallurgy industries etc.. In the fermentation industry, it is used to filter the suspended solid in the fermentation broth. On the basis of several patented technologies, the shaping effect of polypropylene has been enhanced, it features in smooth surface, high intensity, light weight, corrosive proof, innocuous and odorless. The hydraulic device is employed for pressing and releasing the frames and plates. The electrical contact pressure gauge is available to automatically maintain pressure. The whole Support frame is made by welded steel with high intensity, So it is able to suffer from high pressure, which provides the machine with stable performance and long life. The equipment can be equipped with PLC, relay control and many other safety-guarding devices, therefore Andoreaicniats ating the operation will be automatic and easy to control, and the operator will work safely. Girder is equipped with abrasion-proof nonmetallic tracks, which are formed in one piece. It adopts bridge-type flexible frame. Maximum pressure is 22MPa.

Sterile-diaphragm-stop Valve

This valve can work in an environment of 150°C. The valve core is made of 4F/PTFE and body is made of SS316L. The working life of this valve is 1.5 years under extreme condition, no need to exchange gaskets. Automatic/Manual adjustment are available.